ООО НПП «Сибирские горнопромышленники», Кемерово, Россия

Прокопенко С. А., директор, д-р техн. наук, проф., sibgp@mail.ru

ООО «Сила Сибири», Кемерово, Россия ; Институт горного дела СО РАН им. Н. А. Чинакала, Новосибирск, Россия

Колотов С. А.^1,2, генеральный директор, аспирант

АО «Научный центр ВостНИИ», Кемерово, Россия
Лудзиш В. С., научный консультант, д-р техн. наук, проф.

Исследована пригодность использованных резцов шахтных комбайнов к рециклингу. Установлено, что отходы резцов на третьей, четвертой и пятой стадиях износа обладают свойством рецигодности. Разработана классификация с выделением трех классов пригодности инструмента для дальнейшего использования. Применение классификации для оценки партии отходов традиционных резцов добычного комбайна показало, что утилизационный потенциал для технологии рециклинга режущего инструмента представляют отходы резцов на четвертой и пятой стадиях износа.

1. Shemyakin S. A., Shishkin E. A. Physical and mathematical model of rock destruction by a milling machine cutter. Journal of Mining Institute. 2021. Vol. 251. pp. 639–647.
2. Bolobov V. I., Plashchinsky V. A., Borisov S. V., Le-Thanh B. On the ratio of rock fracture parameters in static and dynamic conditions. Obogashchenie Rud. 2021. No. 5. pp. 3–9.
3. Bolobov V. I., Chupin S. A., Bochkov V. S., Mishin I. I. Service life extension for rock cutters by increasing wear resistance of holders by thermomechanical treatment. Gornyi Zhurnal. 2019. No. 5. pp. 67–71.
4. Gabov V. V., Zadkov D. A., Lykov Yu. V., Gurimsky A. I., Shpilko S. I. Exploiting heading machines at Vorkutaugol JSCs mines. Gornoe oborudovanie i elektromekhanika. 2008. No. 12. pp. 2–6.
5. Averin E. A., Zhabin A. B., Polyakov A. V., Linnik Yu. N., Linnik V. Yu. Transition between relieved and unrelieved modes when cutting rocks with conical picks. Journal of Mining Institute. 2021. Vol. 249. pp. 329–333.
6. Linnik Yu. N., Linnik V. Yu. Mechanisms of maximal loads on cutters and cutting heads of coal mining machines. Gornoe oborudovanie i elektromekhanika. 2021. No. 4(156). pp. 16–21.
7. Dewangan S., Chattopadhyaya S. Critical analysis of wear mechanisms in cemented carbide. Journal of Materials Engineering and Performance. 2015. Vol. 24, Iss. 7. pp. 2628–2636.
8. Appl F. C., Wilson C. C., Lakshman I. Measurement of forces, temperatures and wear of PDC cutters in rock cutting. Wear. 1993. Vol. 169, Iss. 1. pp. 9–24.
9. Shao W., Li X., Sun Y., Huang H., Tang J. An experimental study of temperature at the tip of point-attack pick during rock cutting process. International Journal of Rock Mechanics and Mining Sciences. 2018. Vol. 107. pp. 39–47.
10. Fu L., Du C., Li J., Zheng K. Influence of pick working angle on cutting performance of auger miner’s aiguille. Advances in Mechanical Engineering. 2015. Vol. 7, No. 5. DOI: 10.1177/1687814015585427
11. Ward C. R., Crouch A., Cohen D. R. Identification of potential for methane ignition by rock friction in Australian coal mines. International Journal of Coal Geology. 2001. Vol. 45, Iss. 2-3. pp. 91–103.
12. Yasar S., Yilmaz A. O. Drag pick cutting tests: A comparison between experimental and theoretical results. Journal of Rock Mechanics and Geotechnical Engineering. 2018. Vol. 10, Iss. 5. pp. 893–906.
13. Jeong H., Jeon S. Characteristic of size distribution of rock chip produced by rock cutting with a pick cutter. Geomechanics and Engineering. 2018. Vol. 15, Iss. 3. pp. 811–822.
14. Martin J. A., Fowell R. J. Factors governing the onset of severe drag tool wear in rock cutting. International Journal of Rock Mechanics and Mining Sciences. 1997. Vol. 34, Iss. 1. pp. 59–69.
15. Cheluszka P., Mikuła S., Mikuła J. Conical picks of mining machines with increased utility properties—Selected construction and technological aspects. Acta Montanistica Slovaca. 2021. Vol. 26, No. 2. pp. 195–204.
16. Bołoz L. Directions for increasing conical picks’ durability. New Trends in Production Engineering. 2019. Vol. 2, Iss. 1. pp. 277–286.
17. Bołoz L., Kalukiewicz A., Galecki G., Romanyshyn L., Romanyshyn T. Conical pick production process. New Trends in Production Engineering. 2020. Vol. 3, Iss. 1. pp. 231–240.
18. Prokopenko S. A., Ludzish V. S., Kurzina I. A. Improvement of cutting tools to enhance performance of heading machines in rocks. Journal of Mining Science. 2016. Vol. 52, No. 1. pp. 153–159.
19. Prokopenko S. A., Ludzish V. S., Li A. A. Recycling possibilities for reducing waste from cutters on combined cutter–loaders and road builders. Waste Management & Research. 2017. Vol. 35, Iss. 12. pp. 1278–1284.
20. Tangential rotary cutters. Gorny instrument Ltd. Available at: https://www.gornygroup.com/products/mining/underground/tangential/ (accessed: 05.04.2024).
21. Prokopenko S., Vorobiev A., Andreeva L., Janočko J. Waste cutters utilization in underground coal mining. Acta Montanistica Slovaca. 2018. Vol. 23, No. 1. pp. 81–89.
22. Prokopenko S. A., Ludzish V. S., Kurzina I. A., Sushko A. V. Results of industry testing of multiple use rock-cutting picks. Gornyi Zhurnal. 2015. No. 5. pp. 67–70.
23. Cheluzska P. Computer-aided design of robotized technology for manufacturing working units of mining machines. International Journal of Mining, Reclamation and Environment. 2015. Vol. 29, Iss. 1. pp. 62–81.
24. Klishin V. I., Gerike B. L., Nikitenko S. M., Krestovozdvizhensky P. D. Types and causes of failure of tangential-rotary cutter bits. Gornyi Zhurnal. 2016. No. 7. pp. 92–95.
25. Krauze K., Mucha K., Wydro T., Pieczora E. Functional and operational requirements to be fulfilled by conical picks regarding their wear rate and investment costs. Energies. 2021. Vol. 14, Iss. 12. ID 3696.